What can we help you with?

To connect your SOLEM product via Bluetooth, follow these steps:

• 1. Download and open the MySOLEM application on your smartphone.
• 2. Activate Bluetooth and nearby device location on your smartphone.
• 3. Select the “+” or press “add a controller” to add a new product.
• Follow the on-screen instructions to complete the pairing.

• - Green LED: normal operation.
• - Flashing green LED: a channel is in progress (the number of flashes corresponds to the number of the activated station).
• - Blinking orange LED: Firmware update in progress.
• - Orange LED 4 flashes: short-circuit on a station.
• - Static red LED: the product is in initialization mode for 2 minutes.
• - Fast flashing red LED: fault (Sensor open or flow threshold reached). Watering is suspended but the program continues to run. If the "fault" disappears, the program resumes its course (the number of flashes of the LED corresponds to the currently inactive station).
• - Red LED flashing twice: the programmer has lost the time, reconnect to re-synchronize it.
• - Red LED flashing 3 times: loss of Wi-Fi signal (Wi-Fi key entered incorrectly, product installed too far away or internet cut).
• - Red LED flashing 4 times: one of the stations has a short-circuit or is over-consumption or you have switched the product off and on again twice in a short time while a station was in progress.
• - Red LED flashing 5 times: You have exceeded the time required to initialize the programmer. Repeat the initialization procedure.
• - LED off: the product is not powered.

• - Carry out the following initial checks: have you changed boxes? Is the box's Wi-Fi down or stuck? Is a repeater or PLC faulty? Has the box code been changed?
• - Check the status of the Product LED. Red LED flashing 3 times: loss of access point (too far, the box has been moved or has been deleted following a breakdown of the box).
• - Restarting the box or the access point can solve the problem at first. Wait for it to be operational again.
• - Redo the box association procedure. Note: when you are near the controller it will automatically give priority to the Bluetooth connection.

Box association procedure
If when you leave the Bluetooth range of the LR-MB, it switches to "Disconnected" status on the MySOLEM application, this means that the association with your Wi-Fi network has not been carried out correctly or that you are not logged into your MySOLEM account (in this case log in or create a MySOLEM account.)

1. 1. Disconnect and reconnect the LR-MB electrically so that it enters “association” mode for approximately 2 minutes.
2. 2. Click on the button +/ add a controller and select the type of product "LR-MB".
3. 3. Click on “Associate”, the list of available Wi-Fi networks appears.
4. 4. Select your home's Wi-Fi network then enter the Wi-Fi key (if your Wi-Fi network is not displayed, this may mean that your programmer is out of range or that the box's Wi-Fi is down (restart the box), you will then need to add a repeater or CPL Wifi boxes in order to extend your Wi-Fi network).
5. 5. Check that it works by disabling Bluetooth and Wi-Fi on your phone (the programmer should remain in connected status and the Bluetooth symbol, appearing at the top right of your product image, should be replaced by the symbol of a planet with www).

• - Carry out the following initial checks: have you changed boxes? Is the box's Wi-Fi down or stuck? Is a repeater or PLC faulty? Has the box code been changed?
• - Check the status of the Product LED. Red LED flashing 3 times: loss of access point (too far, the box has been moved or has been deleted following a breakdown of the box).
• - Restarting the box or the access point can solve the problem at first. Wait for it to be operational again.
• - Redo the box association procedure. Note: when you are near the controller it will automatically give priority to the Bluetooth connection.

Box association procedure
If when you leave the Bluetooth range of the LR-MB, it switches to "Disconnected" status on the MySOLEM application, this means that the association with your Wi-Fi network has not been carried out correctly or that you are not logged into your MySOLEM account (in this case log in or create a MySOLEM account.)

1. 1. Disconnect and reconnect the SMART-IS electrically so that it enters “association” mode for approximately 2 minutes.
2. 2. Click on the +/ add a controller button and select the “Smart-IS” product type.
3. 3. Click on “Associate”, the list of available Wi-Fi networks appears.
4. 4. Select your home's Wi-Fi network then enter the Wi-Fi key (if your Wi-Fi network is not displayed, this may mean that your programmer is out of range or that the box's Wi-Fi is down (restart the box), you will then need to add a repeater or CPL Wifi boxes in order to extend your Wi-Fi network).
5. 5. Check that it works by disabling Bluetooth and Wi-Fi on your phone (the programmer should remain in connected status and the Bluetooth symbol, appearing at the top right of the image of your product, should be replaced by the symbol of a planet with www).

The LoRa irrigation module wakes up its radio every 3 minutes, so irrigation will start within a maximum of 3 minutes.

View Video Tutorial

• MyINDYGO: for the use of INDYGO swimming pool products only.
• MySOLEM : for the use of SOLEM irrigation and outdoor lighting products.
• MyGARDEN : for the use of products dedicated to managing your garden: irrigation, swimming pool and lighting.

For each product, the application to be used is indicated in the instructions.